P/N

Description

Purpose

Functions/Output

   105.001

Gauge Tester

-To simulate the gauge resistive sensor.

-To simulate the capacitance fuel sensor on Ford vehicles models XD, XE, XF.

-Variable resistor from 0 to 500 Ohms for resistive type senders.

-0 to 4.5V for capacitance tank unit senders (Ford).

    105.003

Tachograph Calibrator 12/24V

-To calibrate Kienzle tachograph 

model No. 1310 and 1318

(Unit limited to VDO Service Agents)

-Voltage range: 12/24V or 2x 9V batteries.

-Tachograph calibrator.

-Pulse counter.

-Frequency generator.

      105.005

Rev-Switch calibrator 12/24V

-To calibrate the 411.101 Rev-Switch.

(the calibrator is designed to simplify Rev-Switch calibration)

-Frequency calibration and input display on Channel 1&2.

105.014

Portable Frequency Generator

-To generate a square wave with 50% duty cycle to test speedo, tacho flow-meter, etc.

(A multimeter can be used to read to read the generator’s output frequency)

-Voltage: 2x  9V battery

-Range: 0-1000 Hz   or   0-5000 Hz.

-Output signal: 0-18V (with fully charged batteries), square wave 50% cycle.

12415

Dual Ratio Interface 12/24V

-To allow the speedometer’s calibration to be constantly accurate in vehicles with two diff ratio, where two different number of impulses per Km are obtained ( High and Low ratio ).

-Range:  From 2510 to 800,000 Impulses/Km.

-Two separate row of switches setting for the two different Imp/Km.

-Electric change-over switching to select correct speedo calibration

  for diff ratio change.

170.12V

Adjustable Switch Module 12V

-To trigger an alarm or activate external devices, adjustable between 0 and 400 Ohms.

(Not suitable for bi-metal gauges)

Suitable for resistive sender’s gauges.

-Output: Relay contacts 3A N/O

170.24V

Adjustable Switch Module 24V

“as above”

“as above”

    170.Timer12V

Timer 12V

Delay timer, adjustable

-Range:  0-30 Seconds

              0-30 Minutes

-Output: Relay Contacts 3A Common, N/C & N/O

320.770

Temperature Switch

General purpose switch to operate a light, buzzer, external relay (thermofan), etc.

Voltage range: 12V

Output: 3 A relay Switches to Negative

332.706

Low voltage warning switch

To operate a 2W warning light globe.

Voltage range: 12/24V

Output: 1 A contacts switching to negative

Adjustment range: From 9 to 31V

410.054

Low water level switch 4-20 mA input

Electronic switch to operate a relay contact at a pre-set water level.

Eg: Warning light, buzzer, pump motor via external relay, etc.

Range: 4-20 mA

Output: 3 A relay contacts switching to negative

410.070

Voltage Monitoring Switch

General purpose module designed to give volt-free changeover contact output for both high and low voltage alarm situations in 12V circuits.

Voltage range: 12V

Output: 3 A Common - N/C - N/O

Adjustment range: From 9 to 31V

411.088

Signal Amplifier/Frequency Divider

To amplify and divide the signal input (Square or Sine wave) by a binary number 1, 2, 4, 8, 16, 32, 64, 128

Voltage range: 12/24V

Output: 0.7 to 10 Volt  (50% duty cycle)

411.089

Frequency Doubler

To double the input frequency plus two output (One out of phase eg: for the 1318 tachograph)

Voltage range: 12/24V

Output: 0.7 to 10 Volt  (variable duty cycle)

411.095

Signal Amplifier/Frequency Divider

To amplify and divide the signal input (Square or Sine wave) by a binary number 16.

Voltage range: 12/24V

Output: 0.7 to 10 Volt  (50% duty cycle)

411.096

Signal Amplifier/Frequency Divider

To amplify and divide the signal input (Square or Sine wave) by a binary number 1, 2, 4, 8, 16.

Voltage range: 12/24V

Output: 0.7 to 10V Square wave

411.100

Signal Interface

-To convert sine to square wave a

-To divide signal by a binary 

 number 1, 2, 4, 8, 16

-To convert sine/square wave to a

  Pulse Width Modulated (PWM) signal

  (adjustable)

Voltage range: 12/24V

Output: 0.7 to 10V Square wave

1) Two output square wave (One 180 Deg out of phase for the two inputs required for the 1318 Tachographs)

2) One Pulse Width Modulated output for various application where a PWM is required)

411.101

Rev-Switch

Frequency driven, electronic switching device to switch a relay at a pre-set frequency with a variable pre-adjusted hysteresis.

Two Input/Output.

Replaces early Rev-Switch box from

p/n 411.061 to 411.066

Range: Channel 1, 2 to 900 Hz  or  15 to 5000 Hz     Channel 2, 2-900 Hz

Hysteresis: 5-95% for both Channels

Signal Input: 2 to 30 ppV Sine/Square wave

Output: 5A relay isolated contacts for each channel, N/O or N/C.

411.105

Signal divider/multiplier

Electronic Ratio Box.

It multiply or divide the input signal by a maximum factor of 3 (In steps)

Voltage range: 12/24V

Output: Square wave 0.7 to 10V or Open collector transistor